Body size: 230 x 150 x 230. The main production: China. Dried work was is baked in the oven, ready to take the heat. Here [How to make basic Hen] than , described as an example of a basic form of the vessel, such as a photograph. First, repeated practice, Learn the basics of “potter’s wheel club”. Preparation of the potter’s wheel ground – knead the soil – to make it easier to handle the soil, kneaded well before entering the ground potter’s wheel. If this time is not kneaded uniformly or air entering, cause deformation or cracks. In this case, if evenly trying careful not to enter into the air Nere, while allowing tapping the clay in the palm of your hand adjust to the mountain type as shown in the photo – put a lump of soil in the “center” of the turntable – in order to produce a clean form, important to keep firmly the center of the earth. When the center is deviated, it will not be able to soil when the ground potter’s wheel to make a good form Te shake. Hand to dry put the rotary table of the “center” to the soil, the to soil pressed against a rotating platform to put the power to make “contact” to rotate the potter’s wheel, plenty of put the water in hand, rub the water into the soil was the character of the “clause”, served in such a manner as to wrap the earth, firmly tighten the armpit to the mass of soil in a cylindrical shape, to secure the arm potter’s wheel ground – create a form – When you are ready to finally potter’s wheel ground get to work. In order to improve the slip, try to work in state hands and soil that are always wet. Once you have a hole, as it is with scissors the soil with both hands of a finger trying to thumb to the surface to be spread gradually bottom on the outside become as much as possible flat, [4] we stretched out little by little from the bottom to the top of the favorite form comes up and tries to stretch [3] to [point], once repeated to, because the soil will be torn off, let’s move is going Let’s left and right hands stretched little by little at the same force-speed. And put the way of force is changed, it is non-uniformity in the thickness of the work, the cause of the cracks, etc. To the processing of mouth – power that once stopped the potter’s wheel, attach the “arm wearing a bow” and “pillars” to the body Serve with hand to “arm” to rotate the potter’s wheel put. Cut off the rough mouth while gradually lower the “arms”. 1 was rotated to remove the extra soil to lift on each “arm”, to use the belly of the thumb and index finger wearing plenty of water, smoothly adjust the cut – cut off from the rotary table – using the “disbursement ki” disconnect the work from the rotary table. Since the cause of the failure and to work with puzzled, trying to put some momentum. Once you stop the potter’s wheel, with a “guide” to the position of No. 1 under the posts, after attaching the one side of the ring of “lining up ki”, “lining up ki” rotate the potter’s wheel Turn the rotary table careful not to get tangled in! Put your finger into the other end of the ring, pull it forward in a state in which the thread of “lining up ki” is a taut so as to be parallel to the rotary table, and slowly lift with thumb to separate the work from the potter’s wheel, the index finger, the middle finger , prepared in advance, to dry and put on a table to put the work before firing preparation – drying the first time – [1] placed in well-ventilated place that is not exposed to direct sunlight, to a semi-dry state [2] there is no stickiness of the surface, since the [point] and drying of the condition to enter the “cut” dries to form also will not collapse for the hand varies depending on the season and climate, enough is frequently checked to try and drying If you do not, the form of the work to the extent that touched is distorted lightly – cut – cut the body to become part, because the weak force from the [point], inside which adjust the shape of the work, the shavings always, scraping the outside water In addition Nere, use can be reused “shaving stick” and “Hera”, will cut the portion to be the body of the “outside” of the work. Although good to leave a try scraping the remains of the confirmation so diligently becomes uniform thickness, if you want to smooth the surface of the work, with a small amount of water to the fingertips, into the firing finally this grilled leveled with a finger. [Point], such as an oven for the paper may be covered with. Placed in an oven to put the work into an oven dish that comes with the microwave oven of the home that can change the hue of the work by changing the arranging and baking time leaving a space so as not to stick the works to each other, (height adjustment If there is, placed in the lower part) the temperature was set to 130 degrees, depending on the size and thickness of the piece to burn 30 to 40 minutes, finishing are different. Do not burn more than an hour of the provisions. Once baked [3] there is a possibility that too baked soil becomes brittle, cool as it is for 1 to 2 hours in an oven range. Work of the oven is very hot, because there is a risk of burns, removed from the always cool. When completely cool finished! Note: All of our items, unless otherwise stated as follows. Manuals are in Japanese. Games are in Japanese / Language is also Japanese. Voltage is 100V (50/60Hz) / Plug is Type-A. Region code is DVD: Region 2 / Blu-ray: Region A. If Lithium-Ion battery is included in products, we will install it into the device for safety regulation of carriers. If you have allergies, please check ingredients and ask us before your order. We will NOT guarantee nor pay for all sickness of allergies caused through usage of products. We accept return request within 30 days after you place an order. International Buyers – Please Note. We do not mark merchandise values below value or mark items as “gifts” – US and International government regulations prohibit such behavior. It is buyers responsibility for assuring that products can be lawfully imported to the destination country. Buyers must comply with all the laws and regulations of the destination country. We could NOT take any liabilities nor responsibilities for injury, sickness, and all the other inconveniences caused through usage of products. The item “ROKURO CLUB Potter’s wheel club from Japan New” is in sale since Sunday, September 10, 2017. This item is in the category “Crafts\Sculpting, Molding & Ceramics\Ceramics & Pottery\Pottery Wheels”. The seller is “koji1101″ and is located in NAGANO. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

• Brand: Takara Tomy
• MPN: N/A